Qfinder pro not finding qnap1/22/2024 Per the instructions, I enter the username "admin" and password "admin," and the message I get is "Login Failure: Invalid Username or Password." Any ideas on where to start with a username and password for admin use?Įdit: I have restarted the NAS, but that has not helped.Įdit 2: I have completed an "Advanced System Reset" with the hope I could start from scratch, but this has also not helped. enabled local master browser on the NAS and done a restart of all devices with the NAS doing a full boot before any other. *The default username and password is admin/admin. Interestingly, if I restart the NAS while my computer is running, there is a 30 second period where Qfinder (6.4.2) registers the NAS and I can even login to it, but it disappears from Qfinder after the long beep sounds. For more details on using Qfinder, please see the tutorial. The step by step process provided by QNAP online states:Īfter completing the installation process (or if your device has pre-installed firmware) you can connect to the NAS using Qfinder. I've been able to install the hardware, latest firmware and format the drives, but cannot get the Qfinder running because I don't have an admin username and password - I haven't established this because at no point during the set up so far has there been a request to provide a username and password for the admin account. I feel like I am a little lost at this point - I follow you that I need an admin account rather than the QID on the NAS web interface, but I am stuck. Why can I log in online per the set-up instructions with no issues and when I try through Qfinder, it says " Incorrect Username or Password?" Please help! I want to complete this install instead of return the unit. I ran across some statements about the default "admin" username, but that doesn't help me if I've set up my account.ĭisks: WD 2TB Reds were read and formatted with no issues I read the QNAP manual and have searched for a few hours since then, on this forum as well as Googling away elsewhere, but I cannot figure out why I cannot login to Qfinder. The response: " Incorrect Username or Password." So, now I am stuck, after about 30 minutes into installation. I enter the very same login info I used to set up the web based myQNAPcloud site and hit enter. I hope you know what I am about to write, because that would make this sooo easy. So, I install the Qfinder program, launch it and it locates my unit. At this point I wonder to myself, where is the desktop dashboard I need to operate this NAS? I Google some more and it seems as if it is the Qfinder program. This statement gives absolutely no clues on how to install the QNAP centric ".qpkg" file type, so after some Googling, I see that I need to install the Qfinder utility. To access the NAS, simply click the name of the service and follow the on-screen instructions. The default NAS IP address is 169.254, as indicated above. Using Qfinder Pro, you can locate all QNAP NAS that are connected to your network. I go online and login to myQNAPcloud and the infamous "Please install the CloudLink QPKG" statement comes up when I try to get to the next step of install. If you already know the IP address of your NAS, you can enter it into the address bar of your browser. Installed the hardware, installed the firmware, clicked "Cloud Installation" and entered the appropriate Cloud Key and go through the account set-up process. I went through the set-up scenario as prescribed by QNAP. I read tons of reviews about how easy this unit is to set up and I agree, up to the point I got stuck. Qfinder pro can't find the NAS and gives me a message that says "cannot connect to device.Hi All, I am new to the forum - just received the TS-231 today. For arguments sake (example, not real numbers) let's say the IP addresses are 123.456.0.1 and 123.456.0.2 and both have the subnet 255.255.255.0. The problem comes when I connect both devices directly using the 10Gbps connection using an RJ45 cable. I can connect to the internet in both devices. I could access it through the web interface, I could find it in Qfinder Pro and I could map the drives to both my wifes Windows 10 laptop and my Macbook pro and. Locate the NAS in the list, and then double-click the name or IP address. Qfinder Pro has no issues finding the qnap. Qfinder Pro automatically searches for all QNAP NAS devices on the network. I have my qnap (tvs-672xt) and PC connected to my switch (using the 1Gbps connections). How do I find and manage QNAP NAS using Qfinder Pro Qfinder Pro allows you to quickly find and manage QNAP devices on the same LAN. Also, I am using a regular RJ45 ethernet cable. What operating systems support Qfinder Pro Qfinder Pro can be installed in any Windows version that is supported by Microsoft, as well as macOS and Ubuntu. If you are using QuFirewall make sure to add your computer's IP address to the "firewall profiles". Add both your NAS and PC to the same subnet (which is what I was always doing). This is for anyone looking for this answer.
0 Comments
Leave a Reply.AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |